🔋 حاسبة تيار قصر دائرة الجهد العالي
حوّل سعة القصر في المنبع (MVA) إلى تيار قصر أولي وتحقق من سعة القطع المطلوبة لمعدات تبديل الجهد العالي — KYN28A لجهد 10 kV و KYN61 لجهد 35 kV.
⚙️ النظام
📊 Result
للمهندسين الذين يحددون معدات تبديل الجهد المتوسط وسعة قطعها.
كيف يتم الحساب
· تيار قصر الدائرة: Isc = Ssc ÷ (√3 × U).
· تيار الذروة: ip ≈ 2.5 × Isc.
· الاختيار: سعة القطع المطلوبة ≥ Isc؛ التيار المقنن = أقرب إطار قياسي أعلى من الحمل.
المعايير المرجعية
| Standard | Scope |
|---|---|
| IEC 62271-100 | معدات التبديل والتحكم للجهد العالي — قواطع دائرة التيار المتردد |
| IEEE C37 | تصنيفات قواطع الجهد العالي (ANSI) |
مثال محسوب — 500 MVA عند 10 kV → 28.9 kA
1. Ssc = 500 MVA، U = 10 kV → Isc = 500 ÷ (√3 × 10) = 28.9 kA.
2. سعة القطع المطلوبة = 31.5 kA؛ تيار الحمل 1000 A → إطار 1250 A.
3. الطراز الموصى به: KYN28A-12-1250-31.5.
FAQ
How do I calculate high-voltage short-circuit current from upstream capacity?
Convert upstream short-circuit capacity Ssc to current: I = Ssc / (sqrt(3) x Un). A 10 kV bus with 500 MVA upstream gives I = 500 / (sqrt3 x 10) = 28.9 kA. Add Transformer and cable impedance for downstream points. The calculator checks this against KYN28A/KYN61 Switchgear ratings (25/31.5/40 kA).
What short-circuit rating does 10 kV switchgear need?
KYN28A 10 kV switchgear is commonly rated 25 kA, 31.5 kA or 40 kA. Most urban 10 kV networks (300-500 MVA upstream) need 25-31.5 kA; industrial plants close to a large source may need 40 kA. The calculator verifies the fault level against the panel rating and flags undersizing.
How is the peak making current related to the RMS breaking current?
The peak (making) current is the maximum instantaneous Fault Current, about 2.5 times the RMS breaking current for a typical X/R Ratio of ~14. A 31.5 kA breaker has a ~80 kA peak making rating. Switchgear must withstand both; the calculator reports the breaking level for selection.
What is the difference between KYN28A and KYN61 switchgear?
KYN28A is metal-clad, removable (withdrawable) 12 kV switchgear with a vacuum circuit breaker, rated up to 40 kA, the mainstream indoor 10 kV switchgear. KYN61-40.5 is the 35 kV equivalent, rated up to 31.5-40 kA. The calculator selects the appropriate class by voltage and fault level.
How do I derate switchgear for high altitude?
Above 1000 m, reduced air density lowers dielectric strength and cooling, so switchgear is derated about 1% per 100 m (IEC 62271-1). At 2000 m a 31.5 kA panel derates to roughly 28-29 kA. The calculator applies altitude derating when checking the panel rating against the fault level.
تضمين هذه الحاسبة
أضف هذه الحاسبة إلى موقعك مجانًا. يتكيف إطار iframe مع أي عرض ويعمل بالكامل داخل متصفح زوارك.
أدوات ذات صلة
تقديرات مرجعية (فوب تشينغداو، إكسو) لأغراض التصميم الأولي فقط — وليست عرضًا نهائيًا. تأكد من التحجيم وفقًا لمشروعك والمعايير المحلية.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.