🔗 Калькулятор падения напряжения в ФЭ-кабеле
Проверьте падение напряжения и потери в линии постоянного тока ФЭ-цепочки, допустимый ток кабеля (1,25 × Iск) и подберите минимальное сечение в пределах норматива падения 2%.
🔗 String & Cable
📊 Voltage-Drop Result
Для монтажников солнечных электростанций, подбирающих кабели постоянного тока и разъёмы.
Как это рассчитывается
· Сопротивление в обе стороны: R = 2 × ρ × L ÷ A (ρ медь 0,0175 Ом·мм²/м).
· Падение напряжения: ΔU = I × R; ΔU% = ΔU ÷ V_цепочки × 100.
· Проверка допустимого тока: требуется ≥ I × 1,25; номинал разъёма (MC4) ≥ I × 1,25.
Применяемые стандарты
| Standard | Scope |
|---|---|
| IEC 60364 | Низковольтные электроустановки (допустимый ток кабеля) |
| NEC 690 | Солнечные фотоэлектрические системы (допустимый ток проводника 1,25 × Iск) |
Решённый пример — 13 A на 50 м → 1,42% при 4 мм²
1. Ток цепочки 13 A, расстояние 50 м, 4 мм², напряжение цепочки 400 В.
2. R = 2 × 0,0175 × 50 ÷ 4 = 0,44 Ом; ΔU = 13 × 0,44 = 5,7 В = 1,42%.
3. Допустимый ток: 13 × 1,25 = 16,3 A ≤ 32 A (4 мм²) — в норме.
4. 1,42% в пределах норматива 2% — сечения 4 мм² достаточно.
FAQ
What voltage drop is acceptable in a PV DC cable?
Design practice limits total DC-side voltage drop to about 2% (IEC 60364 and common PV guidelines), split roughly 1% in the string cabling and 1% in the DC run to the inverter. Higher drop means lost energy — every 1% of drop is roughly 1% of lost annual yield. The calculator checks the drop and recommends the minimum cross-section.
How do I size a PV cable for ampacity?
PV DC cables must carry the string short-circuit current with a safety factor (usually 1.25x Isc, and 1.56x per NEC). For a 550 W module with Isc ~13.9 A and a two-parallel-string combiner, the combined current is ~35 A, so a 6 mm2 copper cable (rated ~40-45 A) is typical. The calculator verifies ampacity and derating.
Copper or aluminum for PV DC cabling?
PV string and DC cables are almost always copper because DC circuits are low-voltage and ampacity-sensitive; aluminium would need a much larger cross-section for the same drop. Copper is also easier to terminate on MC4 connectors. Aluminium appears only in long AC medium-voltage collector runs. The calculator defaults to copper for DC.
How long can a PV DC cable run be?
DC run length is limited by the 2% voltage-drop budget. For a 10 kW string at 500 V DC and 20 A, a 4 mm2 copper cable can run roughly 40-60 m before exceeding 2%. Longer runs need 6-10 mm2 cable or a higher system voltage. The calculator computes the maximum length for a given cross-section.
What DC cable type is used for solar arrays?
PV arrays use double-insulated, UV-resistant solar cable (H1Z2Z2-K / EN 50618, rated 1.5 kV DC and -40 to +90 deg C) for outdoor runs. Single-core copper, usually 4-6 mm2 for strings and 10-35 mm2 for DC mains. The calculator selects cable by ampacity and drop and cites the applicable standard.
Встроить этот калькулятор
Добавьте этот калькулятор на свой сайт бесплатно. Iframe адаптируется к любой ширине и полностью работает в браузере вашего посетителя.
Связанные инструменты
Справочные оценки (FOB Циндао, EXW) только для предварительного проектирования — не окончательное предложение. Подтвердите расчёт по вашему проекту и местным стандартам.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.