⚡ Калькулятор тока короткого замыкания
Рассчитайте ожидаемый ток короткого замыкания по мощности трансформатора в кВА и полному сопротивлению, затем получите номинальный ток и отключающую способность автоматического выключателя — в стандартных типоразмерах IEC или NEC.
⚙️ Трансформатор & Система
📊 Result
Для проектировщиков и подрядчиков, подбирающих низковольтное распределительное оборудование и выключатели по уровню токов КЗ.
Как это рассчитывается
· Номинальный ток: In = кВА ÷ (√3 × U).
· Ток короткого замыкания: Iск = In ÷ (Z%/100).
· Ударный ток: iуд ≈ 2,5 × Iск; номинал выключателя ≥ 1,25 × In, а отключающая способность ≥ Iск.
Применяемые стандарты
| Standard | Scope |
|---|---|
| IEC 60909 | Расчёт токов короткого замыкания в трёхфазных системах переменного тока |
| IEC 60947-2 | Автоматические выключатели низкого напряжения — номинальная отключающая способность |
| NEC 110.9 | Отключающая способность устройств защиты от сверхтоков |
Решённый пример — трансформатор 1000 кВА → ток КЗ 24 кА
1. 1000 кВА, 0,4 кВ, Z = 6% → In = 1000 ÷ (√3 × 0,4) = 1443 A.
2. Iск = 1443 ÷ 0,06 = 24,1 кА; ударный ток iуд ≈ 2,5 × 24,1 = 60 кА.
3. Номинал выключателя = 1600 A (IEC) с отключающей способностью 25 кА.
4. Рекомендуемый низковольтный шкаф: GGD-1600.
FAQ
How do I calculate short-circuit current?
Use IEC 60909: short-circuit current = voltage / (sqrt(3) x total impedance). For a 0.4 kV system, the Transformer impedance dominates. A 1000 kVA, 6% impedance transformer contributes about 24 kA at the LV bus (1000 / (sqrt3 x 0.4 x 0.06) ~ 24 kA). The calculator computes three-phase and single-phase fault currents.
What breaker breaking capacity do I need?
The breaker breaking capacity must exceed the prospective Fault Current at its location. For 24 kA at the bus, select a 36 kA breaker (standard IEC 60947 ratings are 16/25/36/50 kA). Undersizing risks a failure to interrupt a fault, so use a 1.25-1.5 safety margin. The calculator matches the breaker to the fault level.
What is the difference between Icu and Ics?
Icu is the ultimate breaking capacity — the breaker can interrupt it once but may need replacement. Ics is the service breaking capacity — the breaker can interrupt it repeatedly and remain usable. Ics is typically 50-75% of Icu. Select breakers whose Icu exceeds the fault level; the calculator checks against standard ratings.
How does cable length reduce short-circuit current?
Long cables add impedance that reduces fault current downstream. A 50 m run of 35 mm2 copper cable can cut a 24 kA fault to roughly 15-18 kA at the far end. This is why downstream breakers can be lower-rated. The calculator accounts for cable impedance when computing the fault level at the load.
What is the difference between symmetrical and asymmetrical fault current?
Symmetrical fault current is the steady AC component; asymmetrical adds a decaying DC offset, peaking in the first half-cycle. The peak (making) current is 1.5-2.5 times the RMS symmetrical value, so Switchgear has both a breaking (Isc) and a making (peak) rating. IEC 60909 computes both; the calculator reports the symmetrical level for breaker selection.
Встроить этот калькулятор
Добавьте этот калькулятор на свой сайт бесплатно. Iframe адаптируется к любой ширине и полностью работает в браузере вашего посетителя.
Связанные инструменты
Справочные оценки (FOB Циндао, EXW) только для предварительного проектирования — не окончательное предложение. Подтвердите расчёт по вашему проекту и местным стандартам.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.