🔗 Công cụ tính sụt áp cáp PV
Kiểm tra sụt áp phía DC và tổn hao đường dây của chuỗi pin quang điện, xác minh khả năng mang dòng của cáp (1.25 × Isc) và chọn tiết diện tối thiểu nằm dưới hướng dẫn sụt áp 2%.
🔗 String & Cable
📊 Voltage-Drop Result
Dành cho thợ lắp đặt điện mặt trời chọn kích thước cáp DC chính và đầu nối.
Cách tính toán
· Điện trở hai chiều: R = 2 × ρ × L ÷ A (ρ đồng 0.0175 Ω·mm²/m).
· Sụt áp: VD = I × R; VD% = VD ÷ V_chuỗi × 100.
· Kiểm tra khả năng mang dòng: yêu cầu ≥ I × 1.25; định mức đầu nối (MC4) ≥ I × 1.25.
Tiêu chuẩn tham chiếu
| Standard | Scope |
|---|---|
| IEC 60364 | Lắp đặt điện hạ áp (khả năng mang dòng của cáp) |
| NEC 690 | Hệ thống quang điện mặt trời (khả năng mang dòng 1.25 × Isc) |
Ví dụ tính toán — 13 A trên 50 m → 1.42% ở 4 mm²
1. Dòng chuỗi 13 A, khoảng cách 50 m, 4 mm², điện áp chuỗi 400 V.
2. R = 2 × 0.0175 × 50 ÷ 4 = 0.44 Ω; VD = 13 × 0.44 = 5.7 V = 1.42%.
3. Khả năng mang dòng: 13 × 1.25 = 16.3 A ≤ 32 A (4 mm²) OK.
4. 1.42% nằm trong hướng dẫn 2% — 4 mm² là đủ.
FAQ
What voltage drop is acceptable in a PV DC cable?
Design practice limits total DC-side voltage drop to about 2% (IEC 60364 and common PV guidelines), split roughly 1% in the string cabling and 1% in the DC run to the inverter. Higher drop means lost energy — every 1% of drop is roughly 1% of lost annual yield. The calculator checks the drop and recommends the minimum cross-section.
How do I size a PV cable for ampacity?
PV DC cables must carry the string short-circuit current with a safety factor (usually 1.25x Isc, and 1.56x per NEC). For a 550 W module with Isc ~13.9 A and a two-parallel-string combiner, the combined current is ~35 A, so a 6 mm2 copper cable (rated ~40-45 A) is typical. The calculator verifies ampacity and derating.
Copper or aluminum for PV DC cabling?
PV string and DC cables are almost always copper because DC circuits are low-voltage and ampacity-sensitive; aluminium would need a much larger cross-section for the same drop. Copper is also easier to terminate on MC4 connectors. Aluminium appears only in long AC medium-voltage collector runs. The calculator defaults to copper for DC.
How long can a PV DC cable run be?
DC run length is limited by the 2% voltage-drop budget. For a 10 kW string at 500 V DC and 20 A, a 4 mm2 copper cable can run roughly 40-60 m before exceeding 2%. Longer runs need 6-10 mm2 cable or a higher system voltage. The calculator computes the maximum length for a given cross-section.
What DC cable type is used for solar arrays?
PV arrays use double-insulated, UV-resistant solar cable (H1Z2Z2-K / EN 50618, rated 1.5 kV DC and -40 to +90 deg C) for outdoor runs. Single-core copper, usually 4-6 mm2 for strings and 10-35 mm2 for DC mains. The calculator selects cable by ampacity and drop and cites the applicable standard.
Nhúng công cụ này
Thêm công cụ tính toán này vào trang web của bạn miễn phí. Khung iframe thích ứng với mọi chiều rộng và chạy hoàn toàn trong trình duyệt của khách truy cập.
Công cụ liên quan
Giá trị ước tính tham chiếu (FOB Qingdao, EXW) chỉ dành cho thiết kế sơ bộ — không phải báo giá cuối cùng. Hãy xác nhận kích thước theo dự án và tiêu chuẩn địa phương của bạn.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.