So sánh vận hành & bảo trì thủ công với giám sát tình trạng thông minh kết hợp bảo trì dự đoán — chi phí định kỳ, thời gian ngừng hoạt động ngoài kế hoạch, tiết kiệm hàng năm, thời gian hoàn vốn và ROI 3 năm cho đội thiết bị của bạn.
O&M thông minh sử dụng giám sát tình trạng và bảo trì dự đoán để cắt giảm chi phí kiểm tra định kỳ và thời gian ngừng hoạt động ngoài kế hoạch. Công cụ tính này so sánh O&M thủ công với O&M thông minh cho đội thiết bị của bạn và ước tính khoản tiết kiệm, thời gian hoàn vốn và ROI — dựa trên các giả định thận trọng, được minh họa rõ ràng.
Settings are illustrative starting points — confirm with a protection coordination study per IEC 60255 / IEEE 242.
📚 Calculation book
CALCULATION BOOK
1000 kVA - 10kV/0.4kV - single - illustrative
1. Load calculation
Standard: IEC 60076 - IEC 60364-5-52
Parameter
Formula
Value
Connected load
P = sum(kW)
900 kW
Demand factor
Kd
1
Demand power
Pd = P x Kd
900 kW
Power factor
cos(phi) before -> after
0.90 -> 0.95
Design apparent power
Sd = Pd / cos(phi)
947 kVA
Transformer loading
Sd / Srated
95%
2. Short-circuit calculation
Standard: IEC 60909
Parameter
Formula
Value
System impedance (pu)
Zs = S / Ssc
0.20% (on 1000 kVA base)
Transformer impedance
Zt = Z%
4%
Total impedance
Z = Zt + Zs
4.20%
LV prospective Isc
Isc = In / Z
34.4 kA
HV prospective Isc
Isc = Ssc / (sqrt(3) x V)
28.9 kA
Breaking check
Icu >= Isc
LV 36 kA (1.0x margin) PASS
3. Voltage drop
Standard: IEC 60364-5-52 Annex G
Parameter
Formula
Value
Main feeder
dU = sqrt(3) x I x L x R / V
240 mm2 - dU 0.88% @ 60 m
Limit
max 3%
within limit
Transformer volt. reg.
dU ~ loading x Z% x sin(phi)
1.2% at full load
4. Reactive power / harmonics
Standard: IEC 61921 (PFC) - IEEE 519 (harmonics)
Parameter
Formula
Value
Required compensation
Qc = Pd x (tan1 - tan2)
140 kvar
PFC bank
standard step
150 kvar
Detuned reactor
p = 6%
9.0 kvar @ 6% (anti-resonance)
5. Grounding
Standard: IEC 60364-5-54 earthing arrangements and protective conductors LV earthing target 10 ohm (TN systems); 4 ohm used as a conservative design target - target 4 ohm
Parameter
Formula
Value
Single rod resistance
R1 = rho/(2 x pi x L) x ln(4L/d)
39.6 ohm
Rods required
n = R1 / (target x 0.8)
13 rod(s) <= 4 ohm
Rod spec
dia x length
20 mm x 2.5 m
This calculation book is illustrative it consolidates the computed values with the referenced standards. A licensed engineer must verify and seal final design documents for construction.
🔧 Secondary schematic (control & signal)
🔩 Terminal strip (typical)
📏 Standard basis (依据标准)
Topic
Standard
Reliability data
Illustrative industry-typical failure and downtime values — no specific standard
O&M mode:omMode (smart) indicates your current baseline; the calculator always compares manual vs smart O&M so you can see the achievable saving regardless of your starting point.
Illustrative assumptions:O&M cost rates (1.5% / 0.9% of asset value), the 30% failure-reduction benefit and 3% monitoring investment are industry-typical planning values, not guarantees. Actual savings depend on your failure profile and site conditions.
Not a performance warranty:Predictive maintenance reduces, but cannot eliminate, unplanned outages. ROI figures are planning estimates.
Not economical at low failure rates:If your failure rate is already low, the monitoring investment may not pay back — the calculator shows a negative saving in that case.
Scope:This is a commercial O&M comparison tool — it does not design the monitoring system. Contact us for a SCADA / condition-monitoring scope tailored to your assets.
Cách tính toán
Cách tính toán ước tính hoạt động
O&M định kỳ được mô hình hóa theo tỷ lệ phần trăm giá trị tài sản (1,5% thủ công so với 0,9% thông minh). Thời gian ngừng hoạt động ngoài kế hoạch = số lần hỏng hóc × thời gian × chi phí mỗi giờ, với bảo trì dự đoán giúp giảm 30% số lần hỏng hóc theo mức thận trọng. Tiết kiệm hàng năm = chi phí thủ công − chi phí thông minh; thời gian hoàn vốn = đầu tư giám sát ÷ tiết kiệm hàng năm.
Tiêu chuẩn áp dụng
Các số liệu độ tin cậy là giá trị minh họa điển hình trong ngành, không phải tiêu chuẩn. Cơ sở giám sát tham chiếu IEC 61557 và bộ tiêu chuẩn IEEE 3004 (giám sát & bảo vệ) và IEC 60076 cho máy biến áp.
Câu hỏi thường gặp
What is predictive maintenance for power equipment?
Predictive maintenance uses condition monitoring — Dissolved Gas Analysis (DGA), partial discharge, temperature, vibration — to detect faults before failure. It cuts unplanned downtime 30-50% and maintenance cost 10-25% versus reactive maintenance. The calculator compares manual vs condition-monitoring O&M costs.
What is the ROI of smart O&M monitoring?
Smart O&M typically pays back in 1-3 years, driven by avoided downtime (a Transformer failure can cost $50,000-500,000 in outage and replacement) and lower labor. The calculator estimates downtime savings, ROI and payback conservatively for a power-equipment fleet.
What condition monitoring parameters matter most for transformers?
For oil-immersed transformers, dissolved gas analysis (DGA) per IEC 60599 detects incipient faults; oil temperature, moisture and partial discharge round out the picture. For dry-type, temperature and partial discharge dominate. The calculator models a monitoring program covering these parameters.
How much does unplanned downtime actually cost?
Unplanned downtime cost = lost production plus repair and possible penalties. For a process plant a single day can cost $10,000-500,000 depending on the facility. Predictive maintenance targets a 30-50% reduction in such events. The calculator uses your downtime cost and frequency to estimate savings.
What is the difference between preventive and predictive maintenance?
Preventive maintenance services equipment on a fixed schedule regardless of condition, often wasting effort. Predictive maintenance acts only when condition data shows degradation, targeting interventions and cutting cost. Predictive is the higher-ROI strategy for fleets. The calculator models the cost shift from scheduled to condition-based.
Nhúng máy tính này
Sao chép mã iframe bên dưới để nhúng máy tính này vào bất kỳ trang web nào. Trang nhúng có noindex và phù hợp với mọi chiều rộng.
Kết quả là ước tính kỹ thuật để tham khảo. Thiết kế cuối cùng phải được xác nhận bởi kỹ sư địa phương có giấy phép dựa trên điều kiện thực tế và quy chuẩn áp dụng. Giá là FOB Qingdao (EXW) và không bao gồm vận chuyển, thuế hoặc lắp đặt.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.