🔗 Calculateur de chute de tension de câble PV
Vérifiez la chute de tension côté DC et la perte en ligne d'une chaîne PV, contrôlez l'ampacité du câble (1,25 × Isc) et choisissez la section minimale qui reste sous la ligne directrice de 2 % de chute.
🔗 String & Cable
📊 Voltage-Drop Result
Pour les installateurs solaires qui dimensionnent les câbles DC de liaison et les connecteurs.
Comment c'est calculé
· Résistance aller-retour : R = 2 × ρ × L ÷ A (ρ cuivre 0,0175 Ω·mm²/m).
· Chute de tension : VD = I × R ; VD% = VD ÷ V_chaîne × 100.
· Contrôle d'ampacité : requise ≥ I × 1,25 ; calibre du connecteur (MC4) ≥ I × 1,25.
Normes référencées
| Standard | Scope |
|---|---|
| IEC 60364 | Installations électriques basse tension (ampacité des câbles) |
| NEC 690 | Systèmes photovoltaïques (ampacité des conducteurs 1,25 × Isc) |
Exemple détaillé — 13 A sur 50 m → 1,42 % en 4 mm²
1. Courant de chaîne 13 A, distance 50 m, 4 mm², tension de chaîne 400 V.
2. R = 2 × 0,0175 × 50 ÷ 4 = 0,44 Ω ; VD = 13 × 0,44 = 5,7 V = 1,42 %.
3. Ampacité : 13 × 1,25 = 16,3 A ≤ 32 A (4 mm²) OK.
4. 1,42 % est dans la ligne directrice de 2 % — 4 mm² suffisent.
FAQ
What voltage drop is acceptable in a PV DC cable?
Design practice limits total DC-side voltage drop to about 2% (IEC 60364 and common PV guidelines), split roughly 1% in the string cabling and 1% in the DC run to the inverter. Higher drop means lost energy — every 1% of drop is roughly 1% of lost annual yield. The calculator checks the drop and recommends the minimum cross-section.
How do I size a PV cable for ampacity?
PV DC cables must carry the string short-circuit current with a safety factor (usually 1.25x Isc, and 1.56x per NEC). For a 550 W module with Isc ~13.9 A and a two-parallel-string combiner, the combined current is ~35 A, so a 6 mm2 copper cable (rated ~40-45 A) is typical. The calculator verifies ampacity and derating.
Copper or aluminum for PV DC cabling?
PV string and DC cables are almost always copper because DC circuits are low-voltage and ampacity-sensitive; aluminium would need a much larger cross-section for the same drop. Copper is also easier to terminate on MC4 connectors. Aluminium appears only in long AC medium-voltage collector runs. The calculator defaults to copper for DC.
How long can a PV DC cable run be?
DC run length is limited by the 2% voltage-drop budget. For a 10 kW string at 500 V DC and 20 A, a 4 mm2 copper cable can run roughly 40-60 m before exceeding 2%. Longer runs need 6-10 mm2 cable or a higher system voltage. The calculator computes the maximum length for a given cross-section.
What DC cable type is used for solar arrays?
PV arrays use double-insulated, UV-resistant solar cable (H1Z2Z2-K / EN 50618, rated 1.5 kV DC and -40 to +90 deg C) for outdoor runs. Single-core copper, usually 4-6 mm2 for strings and 10-35 mm2 for DC mains. The calculator selects cable by ampacity and drop and cites the applicable standard.
Intégrer ce calculateur
Ajoutez ce calculateur à votre propre site web gratuitement. L'iframe s'adapte à toutes les largeurs et s'exécute entièrement dans le navigateur de vos visiteurs.
Outils associés
Estimations de référence (FOB Qingdao, EXW) pour la conception préliminaire uniquement — pas un devis final. Confirmez le dimensionnement selon votre projet et les normes locales.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.