🔌 Calculateur de dimensionnement de chaîne PV
Concevez une chaîne PV selon les limites de tension de votre onduleur : Voc et Vmp corrigés en température, la fenêtre MPPT et le ratio DC/AC. Évite la surtension par temps froid et la sous-tension par temps chaud.
🔌 Module & Inverter
📊 String Design
Pour les concepteurs et les installateurs solaires qui dimensionnent les chaînes selon les spécifications de l'onduleur.
Comment c'est calculé
· Voc froid : Voc_max = Voc × (1 + α × (Tmin − 25) ÷ 100), α ≈ −0,34 %/°C.
· Vmp chaud : Vmp_min = Vmp × (1 + α × (Tmax − 25) ÷ 100).
· Modules max = floor(Vmax ÷ Voc_max) ; modules min = ceil(MPPT_min ÷ Vmp_min) ; cible ≈ Vmax × 0,85 ÷ Vmp.
Normes référencées
| Standard | Scope |
|---|---|
| IEC 62548 | Champs photovoltaïques — exigences de conception |
| NEC 690.7 | Tension maximale des systèmes PV |
Exemple détaillé — module 550 W, onduleur 10 kW
1. Module 550 W (Voc 49,5 V, Vmp 41,5 V), onduleur 10 kW (Vmax 1000 V, MPPT 90–520 V), Tmin −10 °C, Tmax 60 °C.
2. Voc froid = 49,5 × (1 − 0,0034 × (−35)) = 55,4 V ; Vmp chaud = 41,5 × (1 − 0,0034 × 35) = 36,6 V.
3. Modules max = floor(1000 ÷ 55,4) = 18 ; min = ceil(90 ÷ 36,6) = 3.
4. Recommandé ≈ round(1000 × 0,85 ÷ 41,5) = 18 modules par chaîne.
FAQ
How do I size a PV string against inverter voltage limits?
The string's temperature-corrected open-circuit voltage Voc must stay below the inverter maximum (commonly 1000 V or 1500 V), and the operating voltage Vmp must stay inside the MPPT window. Use the module temperature coefficients: Voc rises roughly 0.25-0.35%/deg C below 25 deg C. A 550 W module with Voc 49.5 V allows about 18-20 in series at -10 deg C on a 1000 V inverter.
What DC/AC ratio should a PV system use?
DC/AC ratio is array DC capacity divided by inverter AC rating. Typical values are 1.1-1.3 for most sites, up to 1.5 in high-latitude or high-albedo locations, to capture more energy when modules rarely reach STC output. Over 1.3-1.4 the inverter clips more peak power, and the marginal energy gain falls below the extra module cost.
Why does temperature affect PV string voltage?
Solar cell voltage drops as temperature rises. Module datasheets give temperature coefficients, typically -0.29%/deg C for Voc and -0.34%/deg C for power. At -10 deg C the voltage is about 10% above the 25 deg C value, so strings must be short enough not to exceed inverter limits in winter; at 70 deg C the voltage is ~13% lower, so strings must stay above the MPPT minimum.
How many modules per string is typical for a 550 W module?
With a 550 W module (Voc ~49.5 V, Vmp ~41.5 V) on a 1500 V inverter, strings of 28-32 modules are common; on a 1000 V inverter, 18-22 modules. The exact count depends on the minimum site temperature and the inverter MPPT range, so the calculator checks both the -10 deg C Voc and the 70 deg C Vmp bounds.
What is the difference between 1000 V and 1500 V PV systems?
1500 V systems allow longer strings (fewer combiner boxes, less cable and DC loss) and cut balance-of-system cost about 3-8% for utility plants, but need 1500 V-rated modules, inverters and protection. 1000 V remains standard for rooftop and small C&I. The calculator's string designer supports both voltage classes.
Intégrer ce calculateur
Ajoutez ce calculateur à votre propre site web gratuitement. L'iframe s'adapte à toutes les largeurs et s'exécute entièrement dans le navigateur de vos visiteurs.
Outils associés
Estimations de référence (FOB Qingdao, EXW) pour la conception préliminaire uniquement — pas un devis final. Confirmez le dimensionnement selon votre projet et les normes locales.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.