🔗 Calculateur de chute de tension
Dimensionnez un câble par ampacité et chute de tension en une seule fois. Choisissez le courant, la longueur et le conducteur, et obtenez la section minimale qui reste dans votre limite de chute de tension.
⚙️ Circuit
📊 Result
Pour les électriciens et les ingénieurs qui dimensionnent les départs BT et les circuits terminaux.
Comment c'est calculé
· Résistance : R = ρ ÷ A (ρ cuivre 0,0225, aluminium 0,036 Ω·mm²/m).
· Chute de tension : VD = √3·I·L·R (triphasé) ou VD = 2·I·L·R (monophasé).
· Chute de tension % : VD% = VD ÷ U × 100 (U = 400 V ou 230 V).
Normes référencées
| Standard | Scope |
|---|---|
| IEC 60364-5-52 | Installations électriques — courants admissibles et chute de tension |
Exemple détaillé — 100 A sur 50 m → cuivre 25 mm²
1. 100 A, 50 m, cuivre triphasé, limite de 3 %.
2. Ampacité d'abord : 25 mm² de cuivre admettent 101 A ≥ 100 A.
3. R = 0,0225 ÷ 25 = 0,0009 Ω/m → VD = √3 × 100 × 50 × 0,0009 = 7,8 V = 1,95 %.
4. 25 mm² satisfont à la fois l'ampacité et la limite de chute de 3 %.
FAQ
What is an acceptable voltage drop in a low-voltage circuit?
IEC 60364-5-52 recommends total voltage drop within 5% (distribution plus final circuit), and 3% for lighting. In practice feeders are sized for 2-3% steady-state drop, leaving margin for motor starting. The calculator computes drop for single and three-phase circuits and recommends a cross-section that meets the limit.
How do I calculate voltage drop for a 3-phase circuit?
Voltage drop = sqrt(3) x I x L x (R cos(phi) + X sin(phi)). For a 100 A, 50 m, 35 mm2 copper feeder (R ~0.524 ohm/km), drop is about 1.73 x 100 x 0.05 x 0.524 = 4.5 V, or 1.1% of 400 V. The calculator computes drop in volts and percent and flags the recommended section.
Copper or aluminum for a feeder cable?
Aluminium is lighter and cheaper (30-50% less) but needs a larger cross-section for the same drop because its resistivity is ~1.6x copper. For a 100 A feeder, 35 mm2 copper roughly equals 50-70 mm2 aluminium. Copper wins in ducts and short runs; aluminium wins in long, cost-driven feeders. The calculator compares both.
How does motor starting affect voltage drop?
Motor starting current is 5-7 times rated, so the starting voltage drop is 5-7 times the steady-state drop. A feeder sized for 2% running drop may dip 10-15% during start, which can stall the motor. Soft-starters or larger cables limit this. The calculator flags starting drop and recommends mitigation.
What cross-section do I need for a 100 A three-phase feeder?
For a 100 A, 0.4 kV three-phase feeder, a 35 mm2 copper cable is the standard choice, carrying ~110-125 A with a 50 m run dropping about 1%. For longer runs or tighter drop limits, use 50 mm2. The calculator picks the minimum section meeting both ampacity and drop per IEC 60364-5-52.
Intégrer ce calculateur
Ajoutez ce calculateur à votre propre site web gratuitement. L'iframe s'adapte à toutes les largeurs et s'exécute entièrement dans le navigateur de vos visiteurs.
Outils associés
Estimations de référence (FOB Qingdao, EXW) pour la conception préliminaire uniquement — pas un devis final. Confirmez le dimensionnement selon votre projet et les normes locales.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.