⚡ Calculadora de Corrente de Curto-Circuito
Calcule a corrente de curto-circuito presumida a partir do kVA e da impedância do transformador e obtenha a corrente nominal e a capacidade de interrupção do disjuntor — em tamanhos padrão IEC ou NEC.
⚙️ Transformador & Sistema
📊 Result
Para projetistas e contratantes que dimensionam painéis de baixa tensão e disjuntores conforme o nível de falta.
Como é calculado
· Corrente nominal: In = kVA ÷ (√3 × U).
· Corrente de curto-circuito: Isc = In ÷ (Z%/100).
· Corrente de pico: ip ≈ 2,5 × Isc; classificação do disjuntor ≥ 1,25 × In e capacidade de interrupção ≥ Isc.
Normas de referência
| Standard | Scope |
|---|---|
| IEC 60909 | Cálculo de correntes de curto-circuito em sistemas CA trifásicos |
| IEC 60947-2 | Disjuntores de baixa tensão — capacidade de interrupção nominal |
| NEC 110.9 | Capacidade de interrupção de dispositivos de proteção contra sobrecorrente |
Exemplo resolvido — transformador de 1000 kVA → falta de 24 kA
1. 1000 kVA, 0,4 kV, Z = 6% → In = 1000 ÷ (√3 × 0,4) = 1443 A.
2. Isc = 1443 ÷ 0,06 = 24,1 kA; pico ip ≈ 2,5 × 24,1 = 60 kA.
3. Classificação do disjuntor = 1600 A (IEC) com capacidade de interrupção de 25 kA.
4. Painel de baixa tensão recomendado: GGD-1600.
FAQ
How do I calculate short-circuit current?
Use IEC 60909: short-circuit current = voltage / (sqrt(3) x total impedance). For a 0.4 kV system, the Transformer impedance dominates. A 1000 kVA, 6% impedance transformer contributes about 24 kA at the LV bus (1000 / (sqrt3 x 0.4 x 0.06) ~ 24 kA). The calculator computes three-phase and single-phase fault currents.
What breaker breaking capacity do I need?
The breaker breaking capacity must exceed the prospective Fault Current at its location. For 24 kA at the bus, select a 36 kA breaker (standard IEC 60947 ratings are 16/25/36/50 kA). Undersizing risks a failure to interrupt a fault, so use a 1.25-1.5 safety margin. The calculator matches the breaker to the fault level.
What is the difference between Icu and Ics?
Icu is the ultimate breaking capacity — the breaker can interrupt it once but may need replacement. Ics is the service breaking capacity — the breaker can interrupt it repeatedly and remain usable. Ics is typically 50-75% of Icu. Select breakers whose Icu exceeds the fault level; the calculator checks against standard ratings.
How does cable length reduce short-circuit current?
Long cables add impedance that reduces fault current downstream. A 50 m run of 35 mm2 copper cable can cut a 24 kA fault to roughly 15-18 kA at the far end. This is why downstream breakers can be lower-rated. The calculator accounts for cable impedance when computing the fault level at the load.
What is the difference between symmetrical and asymmetrical fault current?
Symmetrical fault current is the steady AC component; asymmetrical adds a decaying DC offset, peaking in the first half-cycle. The peak (making) current is 1.5-2.5 times the RMS symmetrical value, so Switchgear has both a breaking (Isc) and a making (peak) rating. IEC 60909 computes both; the calculator reports the symmetrical level for breaker selection.
Incorporar esta calculadora
Adicione esta calculadora ao seu próprio site gratuitamente. O iframe se adapta a qualquer largura e roda inteiramente no navegador do visitante.
Ferramentas relacionadas
Estimativas de referência (FOB Qingdao, EXW) para projeto preliminar — não são uma cotação final. Confirme o dimensionamento com seu projeto e as normas locais.
Send my complete design report
Get the full bill of materials, single-line diagram, calculation steps and FOB pricing as a PDF — free, no sign-up.
Your data stays private. No spam — only a reply to your enquiry.